Categories


RIFLE DOUBLE CAVITY MOULDS LYMAN

sinclairintl reloading equipment

Quick View
$73.99
 
    • View
      • RIFLE DOUBLE CAVITY MOULDS LYMAN

      • Classic Lyman bullet moulds are built from high-grade steel to last for generations. Each dual-cavity mould includes a built-in sprue cutter to trim excess lead. Available in a variety of popular rifle and pistol calibers. Requires Mould Handles, sold below. FN = flat nose; RN = round nose; SWC = semi-wadcutter. Weights given in the table are typical for bullets cast using Lyman #2 alloy.Warning: Melting lead and casting lead objects will expose you and others in the area to lead, which is known to cause birth defects, other reproductive harm and cancer. See Instructions on Reducing Exposure supplied with product.

        Sinclair, Issue:5B, Page:090

LOCK-N-LOAD BULLET FEEDER HORNADY

sinclairintl reloading equipment

Quick View
$276.99
 
    • View
      • LOCK-N-LOAD BULLET FEEDER HORNADY

      • Turns your Lock-N-Load Auto Progressive Press (AP) into a bench-mounted ammo factory. Large hopper automatically feeds up to 200 jacketed or plated pistol bullets to an already primered, powder-loaded case. Adjustable center plate and bullet feed wipers ensure smooth feeding. No special tools needed for adjustment. Requires Lock-N-Load bullet feeder dies, sold separately. Dies available in .380/9mm, .38/.357, .40/10mm, .44 Special Magnum, and .45 Auto cartridges only. Uses 110V AC house current.

        Sinclair, Issue:5B, Page:063

E-ZEE CASE GAGE II LYMAN

sinclairintl reloading equipment

Quick View
$18.99
 
    • View
      • E-ZEE CASE GAGE II LYMAN

      • Easily measure the case length of over 70 popular rifle and pistol cases with Lyman's new E-ZEE Case Gauge II. New Version includes many newer cases (WSM's, 204 Ruger, 500 Sand W and others). This rugged, precisely made metal gage makes sorting or identifying cases fast and accurate. Sinclair, Issue:5B, Page:009

AUTO PRIMING TOOL RCBS

sinclairintl reloading equipment

Quick View
$89.99
  (52)
    • Check Price
      • AUTO PRIMING TOOL RCBS

      • This is a bench mounted priming tool with a fairly good feel and automated primer dropping tubes. Uses standard RCBS press type shellholders. Comes with large and small primer feed tubes and primer rod assemblies for large and small primers. Cases can be primed with this tool without touching the primers with your fingers at all. Big Book Catalog, Issue:68, Page:531 Sinclair, Issue:5B, Page:024

CASE TRIMMER AND KITS SINCLAIR/L.E. WILSON

sinclairintl reloading equipment

Quick View
$66.99 - $129.99
  (39)
    • Check Price
      • CASE TRIMMER AND KITS SINCLAIR/L.E. WILSON

      • The L.E. Wilson Stainless Steel Case Trimmer is the most accurate case trimmer in the world! The unique way the case is held assures your cases are aligned square to the cutter during trimming and that the trimmed length is identical for each case. The L.E. Wilson trimmer uses case holders that hold the case neck by the body taper and utilizes no pilots during the case trimming operation. The trimmer utilizes a rail system that the case holders, cutter housing, and adjustment stop sits on providing perfect alignment with each other. Trimmer case holders are available separately. The L.E. Wilson Stainless Steel Case Trimmer is available in several configurations and can also be used for inside neck reaming, military crimp removal, and case mouth deburring by using additional cutters. L.E. Wilson Standard Case Trimmer – Case Trimmer complete (order trimmer case holders separately). Sinclair/L.E. Wilson Case Trimmer Kit – L.E. Wilson Case Trimmer and Sinclair Mounting Stand with “SharkFin” Case Holder Clamp (order case holders separately.) This mounting stand and clamping attachment make case trimming much quicker and comfortable. The mounting stand can be C-clamped or permanently mounted to a bench top. The “SharkFin” Case Holder Clamp swings quickly into place and provides downward pressure on the case holder while trimming. Sinclair/L.E. Wilson Case Trimmer Kit with Platform – L.E. Wilson Case Trimmer and Sinclair Mounting Stand with “SharkFin” Case Holder Clamp (order case holders separately.) This mounting stand and clamping attachment make case trimming much quicker and comfortable. The mounting stand can be C-clamped or permanently mounted to a bench top. The “SharkFin” Case Holder Clamp swings quickly into place and provides downward pressure on the case holder while trimming. Trimmer platform included. Sinclair/L.E. Wilson 50 BMG Case Trimmer Kit – This kit includes a L.E. Wilson Case Trimmer with a larger diameter cutter than the standard cutter, a Sinclair Mounting Stand with a “Shark Fin” Case Holder Clamp, and a case holder for the 50 BMG. In addition to the 50 BMG, this configuration can also be used with other cartridges down to and including .22 caliber cartridges. L.E. Wilson Stainless Micro Trimmer Only – The L.E. Wilson Stainless Micro Trimmer enables the user to easily make quick trim adjustments in .001" increments. The compact micrometer unit is directly incorporated into the stop bearing. Add a trimmer case holder (sold separately) and you can clamp your trimmer in a bench vise or pair the trimmer with a Sinclair Trimmer Stand w/Clamp. 1911, Issue:11, Page:065 Big Book Catalog, Issue:68, Page:529 Sinclair, Issue:5B, Page:010 Sinclair, Issue:5B, Page:079

PISTOL CARBIDE FACTORY CRIMP DIES LEE

sinclairintl reloading equipment

Quick View
$19.99
  (84)
    • Check Price
      • PISTOL CARBIDE FACTORY CRIMP DIES LEE

      • Sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability The adjusting screw quickly and easily sets the desired amount of crimp Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders Made of steel and features an internal carbide ring Carbide dies do not require the use of case lube

SINCLAIR UNIFORMER KIT WITH SCREWDRIVER ADAPTOR SINCLAIR INTERNATIONAL

sinclairintl reloading equipment

Quick View
$59.99
  (56)
    • Check Price
      • SINCLAIR UNIFORMER KIT WITH SCREWDRIVER ADAPTOR SINCLAIR INTERNATIONAL

      • Save money by purchasing our rifle uniformers in one of the two kits we offer. 1) The hand kit (UN-8K) comes with a large rifle uniformer, a small rifle uniformer, and a handle. 2) The power kit (UN-8KP) comes with a large rifle uniformer, a small rifle uniformer, and a screwdriver power adaptor. 1911, Issue:11, Page:064 Big Book Catalog, Issue:68, Page:528 Sinclair, Issue:5B, Page:003

AR SERIES DIE SETS RCBS

sinclairintl reloading equipment

Quick View
$45.99
  (10)
    • Check Price
      • AR SERIES DIE SETS RCBS

      • A must for the progressive reloader. The RCBS AR Series Die Set features a Small Base sizing die and a Taper Crimp seating die. This combination makes reloading easier for AR-style or semi-auto shooters. The Small Base sizer guarantees that the cartridge will rechamber. The Taper Crimp Seater is more forgiving when various case lengths are loaded at the same time. Case neck crimp bulges and buckled shoulders are virtually eliminated when Taper crimping is used with cannelured bullets. Brownells Christmas , Issue:3X, Page:014 Sinclair, Issue:5B, Page:056

BUSHING FULL LENGTH SIZER AND SEATER DIE SETS WHIDDEN GUNWORKS

sinclairintl reloading equipment

Quick View
$184.99
  (98)
    • Check Price
      • BUSHING FULL LENGTH SIZER AND SEATER DIE SETS WHIDDEN GUNWORKS

      • Whiddens' hand polished Bushing Full Length Sizer and Seater Sets come in most standard calibers . The Full Length Sizer Die has a shorter overall length for better shoulder bump-back, a smaller base and tighter internal tolerances. The Seater Die comes with a micrometer top for precise adjustments. These dies are designed with a floating sleeve system which helps to improve concentricity- a must for repeatable precision. No bushing is included with the set.  The sizer will accept Redding or L.E. Wilson bushings.

Harrell Premium "Culver" Measure W/ Stand SINCLAIR INTERNATIONAL

sinclairintl reloading equipment

Quick View
$309.99
  (36)
    • Check Price
      • Harrell Premium "Culver" Measure W/ Stand SINCLAIR INTERNATIONAL

      • Here's a combination that just makes sense. We've bundled up two of the most popular Harrell powder measures with our own Sinclair Powder Measure Stand for you to save money during the holidays. Choose the Harrell Premium "Culver" Measure, a highly versatile "load anything" measure that holds 16 oz. of powder and throws charges from 6 to 120 grains. The Premium Benchrest Measure is more compact, so its great for loading at the range. It holds 8 oz. of powder and throw charges from 6 to 60 grains. Big Book Catalog, Issue:68, Page:537 Sinclair, Issue:5B, Page:081

CLASSIC CULVER POWDER MEASURE HARRELL

sinclairintl reloading equipment

Quick View
$339.99
  (77)
    • Check Price
      • CLASSIC CULVER POWDER MEASURE HARRELL

      • This is the top-of-the-line Harrell powder measure, and there is probably no finer Culver style powder measure available. The Classic features Harrell's double roller bearing construction, polished and nickel plated main body, green anodized top and bottom sections which screw off and large 16 oz. powder bottle threads. This measure throws from 6 to 120 grains and comes with two four inch drop tubes and one 16 oz. plugged powder bottle. This is a great looking, accurate, durable, and long lasting measure any reloader would be proud to own. Each Harrell measure is built with a quality CNC machined aluminum body and an extremely accurate “Culver Style” brass metering system. All of the measures throw with the same accuracy and repeatability, and can be dialed back to the desired charge on the click metering system at any time. Each Harrell measure comes with a clamp style mounting system, one appropriate sized powder bottle with a bottom plug and two 4" drop tubes, one 3⁄16" and one ¼" ID (Schuentzen has a shorter drop tube). There are no finer custom powder measures on the market. Powder stand not sold with this measure. These can be purchased separately. Big Book Catalog, Issue:68, Page:537 Mini-Catalogs, Issue:15, Page:019 Sinclair, Issue:5B, Page:081

STAINLESS PRIMING TOOL WITH CASE SINCLAIR INTERNATIONAL

sinclairintl reloading equipment

Quick View
$129.99
  (56)
    • Check Price
      • STAINLESS PRIMING TOOL WITH CASE SINCLAIR INTERNATIONAL

      • The Sinclair Priming Tool is one of the finest tools we manufacture. Handloaders around the world have told us “this is the best priming tool in the world”. The Sinclair Priming Tool is manufactured from the finest materials available. The main body, head, and punch housings are all made of stainless steel, the handle is machined from aircraft grade aluminum, and the pins and pushrod are hardened. These materials insure the owner a lifetime of trouble-free use. The Sinclair Priming Tool comes complete with housings and punches for both large and small primers. The tool head utilizes Sinclair Priming Tool Shellholders and locks the case head square to the priming punch. The leverage of the tool is outstanding, yet extremely sensitive so you can feel the primer entering the primer pocket and bottoming out. Our tool is made for single feeding of primers. The Sinclair Priming Tool is expensive but made with consideration for quality and to provide the user with a well-made tool that will last a lifetime and more. There are no plastic parts to wear or break.

73 STYLE STEEL BUSHING - .185 TO .250 REDDING

sinclairintl reloading equipment

Quick View
$15.99 - $16.49
  (34)
    • Check Price
      • 73 STYLE STEEL BUSHING - .185 TO .250 REDDING

      • Heat treated steel bushings. The sizing diameters are hand polished with a surface hardness of Rc 60-62 to reduce sizing effort. Bushings are available throughout the range of .185" thru .368" in .001" increments. The last three digits of the part (#RD73XXX) denotes bushing size. View other sizes: .251" to .305" .306 to .368" Determining Redding Bushing Size The proper bushing size can be easily determined by measuring the outside neck diameter of your loaded cartridges with a precision micrometer or a dial caliper. Then, simply subtract .001" from the cartridge that had the smallest average neck diameter. This diameter bushing will generally size case necks just enough to create the proper press fit for the bullet. If you are using a Type “S” style die and not turning the outside of your case necks, we suggest using a bushing .002" smaller than your smallest average neck diameter, and using the expander ball included with your Type “S” die. This size bushing will still give you minimal sizing (maximizing the life of your brass) and the expander ball will insure that each cartridge has the same bullet grip. Redding has found that when you have cases with neck wall thicknesses on the thin side of the SAAMI tolerance, your fired case will measure considerably larger (.006" to .010" larger) than your loaded rounds. In these circumstances, Redding’s tests have shown that a bushing .001" larger (than the loaded round) may give you the desired bullet grip. Brownells Christmas , Issue:2X, Page:014 Sinclair, Issue:1B, Page:043

BROKEN SHELL EXTRACTOR BROWNELLS

sinclairintl reloading equipment

Quick View
$19.99 - $22.99
  (54)
    • Check Price
      • BROKEN SHELL EXTRACTOR BROWNELLS

      • Easily Removes Broken Cases Without Field StrippingCase head separation from over-fired or out of spec brass won’t ruin your shooting experience if you keep one of these handy tools in your pocket or field kit. Hardened, steel tool reliably and easily removes broken cases from AR-type or any other firearm chambered for the .223/5.56 NATO or .308/7.62 NATO cartridges. Exclusive, threaded, two-piece design is adjustable for overall length, so the tool completely engages the rim of the case mouth; cannot slip through or strip out. Very simple to use, drop the broken shell extractor into the chamber directly inside the broken case. Allow the bolt to close so the extractor engages the rim of the tool and draw back the bolt to open the chamber. The broken case will eject along with the broken shell extractor. AR-15, Issue:11, Page:082 AR-15, Issue:11, Page:083 AR-15, Issue:11, Page:088 Big Book Catalog, Issue:68, Page:082 Big Book Catalog, Issue:68, Page:083 Big Book Catalog, Issue:68, Page:088 Big Book Catalog, Issue:68, Page:468 Big Book Catalog, Issue:68, Page:501 Law Enforcement / Police Store, Issue:08, Page:054 New Product Supplement, Issue:593, Page:021

TYPE S-NECK BUSHING DIES, CATEGORY III CARTRIDGES REDDING

sinclairintl reloading equipment

Quick View
$59.99 - $89.99
  (30)
    • Check Price
      • TYPE S-NECK BUSHING DIES, CATEGORY III CARTRIDGES REDDING

      • Bushing Neck Sizing Die utilizes interchangeable bushings for precise case neck resizing, allowing the reloader to control the amount of neck sizing on his cases. A reloader can eliminate oversizing his brass by selecting a bushing correctly sized for his cases and chamber. Available in over 70 calibers with interchangeable bushings in .001inch increments. The decapping rod comes with a standard expander ball or a decapping pin retainer for sizing without the expander ball installed. Adjustable decapping rod allows positioning of the bushing to resize only the portion of the neck desired. Dies supplied without bushings. Sold separately or as part of a set. Sinclair, Issue:5B, Page:038

GEN II UNIVERSAL FLASHHOLE DEBURRING TOOL SINCLAIR INTERNATIONAL

sinclairintl reloading equipment

Quick View
$9.99 - $19.99
  (57)
    • Check Price
      • GEN II UNIVERSAL FLASHHOLE DEBURRING TOOL SINCLAIR INTERNATIONAL

      • The Lastest version of our Model 1000 flash hole deburring tool features stainless steel construction and chip clearance slots which alleviate the tendency of the tool to collect chips in the end of the cutting shaft. This tool is inserted in the case mouth and uses the web of the case as a safety stop. A couple of turns will remove any burrs and leave a small chamfer on the inside edge of the flash hole. Flash hole deburring is a one-time operation. Since variations of case length do not affect the use of this tool, flash hole deburring is most easily performed on brand new brass without trimming. This tool is available as the 05-1000 standard Generation II flash hole tool which consists of the cutting shaft and the tapered guide. For handloaders who perfer a large, comfortable handle, this tool is also available as the 05-1255 which includes the Sinclair large grip handle found on many of our other tools. For handloaders who already own this or our previous Model 1000 Flash Hole Deburring Tool the large Sinclair handle is available separately as the 05-1320. Big Book Catalog, Issue:68, Page:528 Sinclair, Issue:5B, Page:002

TYPE S BUSHING NECK DIE SETS REDDING

sinclairintl reloading equipment

Quick View
$109.99 - $169.99
  (13)
    • Check Price
      • TYPE S BUSHING NECK DIE SETS REDDING

      • The Type S Bushing Style Neck Die set proveds reloaders with a simple means to precisely control case neck size and tension. Packaged in a Redding Die Box with a wrench and extra decapping pin, this set includes a Type S Bushing Neck Die and a Body Die. Sinclair, Issue:5B, Page:038

SINCLAIR PREMIUM NECK TURNING TOOL W/ HANDLE SINCLAIR INTERNATIONAL

sinclairintl reloading equipment

Quick View
$139.99 - $149.99
  (91)
    • Check Price
      • SINCLAIR PREMIUM NECK TURNING TOOL W/ HANDLE SINCLAIR INTERNATIONAL

      • We feel our NT-4000 Premium Neck Turning Tool is the finest, easiest to adjust, most accurate and comfortable to use hand neck turning tool available. Our Premium Tool employs an eccentric mechanism (not an eccentric mandrel) for quick cut depth adjustments which are accurate to .0001 inch with our carbide mandrels. The click adjustable cutter adjustment knob moves the cutter in either direction in .0002 inch to .00025 inch per click increments. Depth of cut can be adjusted a total of .004-.005 inch using the laser engraved adjustment knob. The Premium Tool comes with three laser marked feeler gages which are used to quickly set the cutter depth to the approximate range of the cut desired, and a mandrel adjustment screw is included to make mandrel set up and adjustment easier. with the cutter in range using the feeler gages, the eccentric adjustment knob will make final adjustment for the exact cut thickness you desire. Cutter adjustment is very fast and sure with none of the usual trial and error experienced with other tools. The ergonomic shape of the tool body makes it very comfortable to use and much less fatiguing over a long neck turning session. Sinclair, Issue:5B, Page:017

TRIM MATE CASE PREP CENTER RCBS

sinclairintl reloading equipment

Quick View
$3.49 - $153.99
  (19)
    • Check Price
      • TRIM MATE CASE PREP CENTER RCBS

      • Reduce the work of the case preparation by using the RCBS Trim Mate Case Prep Center. Five gear-driven rotating heads turn the tasks of chamfering, deburring, primer pocket cleaning, military crimp removal, and flash hole deburring into a much easier job. The tough, high torque motor does all the work, letting you move quickly from station to station. Great companion tool for trimming at the same time. There are two stationary positions for case neck brushes or other accessories and a cupped area for holding dry neck lube. The case Prep Center includes large and small primer pocket brushes, inside chamfering and outside deburring tools, medium and small case neck brushes, and a packet of dryneck lube. There are also number of optional accessories available such as the RCBS Primer Pocket Uniformers that are manufactured with cutters. There are also Military Crimp Removers available that are made with hardened tool steel cutters that ream out the crimp ring found in military cases. A VLD Chamfering tool is available as well. Big Book Catalog, Issue:68, Page:529 Sinclair, Issue:5B, Page:007

VERSA PAK PRO REDDING

sinclairintl reloading equipment

Quick View
$479.99
  (2)
    • Check Price
      • VERSA PAK PRO REDDING

      • Previously sold only in Europe, this ultimate upgrade of the Versa Pak replaces the 1400 XT Case Trimmer with Reddings' unique Micrometer Adjustable Model 2400 Case Trimming Lathe. It also adds the Match Grade model 3BR Powder Measure in place of the Classic Model 3. Full contents: Model 2 Powder And Bullet Scale Model 3BR Powder Measure Model 2400 Match Precision Case Trimming Lathe Powder Trickler Imperial Application Media Imperial Sizing Die Wax Pad Style Case Lube Kit Model 18 Case Prep Kit Deburring Tool Powder Funnel Advanced Handloading DVD Hodgdon Annual Manual Sinclair, Issue:5B, Page:065

COMPETITION BUSHING NECK DIE, CATEGORY I CARTRIDGES REDDING

sinclairintl reloading equipment

Quick View
$110.99 - $131.99
  (76)
    • Check Price
      • COMPETITION BUSHING NECK DIE, CATEGORY I CARTRIDGES REDDING

      • This neck sizing die with interchangeable bushings is similiar in concepts to the Redding Competition Seating die. The cartridge case is completely supported and aligned within the die before sizing begins. As the sizing begins, the case remains supported in the chambered sliding sleeve while the floating sizing bushing centers on the case neck. A micrometer integral to the die body allows the user to precisely control the amount/ length of the neck that will be sized. Dies supplied without bushings. Dies sold separately or as part of a set. Big Book Catalog, Issue:68, Page:534 Sinclair, Issue:5B, Page:036 Sinclair, Issue:5B, Page:038

GOLD MEDAL MATCH FULL LENGTH NECK BUSHING DIE SET RCBS

sinclairintl reloading equipment

Quick View
$134.99
  (74)
    • Check Price
      • GOLD MEDAL MATCH FULL LENGTH NECK BUSHING DIE SET RCBS

      • RCBS® is proud to introduce the Gold Medal series of neck bushing rifle dies. This changeable diameter neck bushing type of die has been used by Bench Rest and Long Range Precision shooters for years. Due to variability in neck brass thickness, RCBS standard dies size the neck below your desired diameter and then pull an expander ball through to get the proper bullet tension. The Gold Medal sizing die features a self-centering, changeable neck bushing that allows you to precisely set the amount of tension on the bullet. This reduces work hardening of the case neck brass, prolonging case life and increasing accuracy. Neck bushings are available in .001” increments from .189” to .365”. The Gold Medal rifle dies are available in Full-Length and Neck sizing styles. By removing the neck bushing, the Full Length sizing die can be used as a “bump” die to set headspace back the desired amount. Neck bushings are not included. RCBS suggests that you have neck bushings one to two sizes above and below your target diameter. RCBS Gold Medal seat dies feature a micrometer adjustable, free floating and self centering bullet seating system with a convenient bullet loading window. The Gold Medal seat die can also be used on progressive presses with the exception of the .221 Rem Fireball, .17 Rem Fireball and .22 Hornet cartridges. Sinclair, Issue:5B, Page:056

BOSS II PRO-PAK REDDING

sinclairintl reloading equipment

Quick View
$349.99
  (46)
    • Check Price
      • BOSS II PRO-PAK REDDING

      • The Redding Pro Pak has been the perfect beginning for generations of America’s most successful handloaders. Previously, this kit was available with either a Boss or Big Boss Press. For 2013, the Pro Pak family has gained a new member. The Redding Pro Pak is now offered with the highly respected Big Boss II press. This 100% American made press features a high density, tight grain structure cast iron frame produced to Redding’s specific formulation at a family-owned Pennsylvania foundry. All Big Boss II components are CNC machined and individually hand fitted in Redding's Cortland NY facility. All of which, assures decades of precise and reliable function even on big cases and tough forming jobs. The Big Boss II also features a unique spent primer removal system, which drops the primer and associated debris straight down through the center of ram and into a captive tube below the press. This keeps dirt, grime and other spurious matter away from the interface of the press frame and ram, thereby protecting the critical surfaces from unnecessary wear and tear during use. The new Big Boss II Pro Pak continues the tradition of a great start into handloading with all of the basic tools needed to build a first loading bench with durable, quality tools in one box at a price which is discounted off the individual pieces. Redding Reloading Equipment has focused on building the finest quality American Made products for the precision handloading market since 1946. Sinclair, Issue:5B, Page:064

SINCLAIR POLY LOADING BLOCK - 50 ROUND SINCLAIR INTERNATIONAL

sinclairintl reloading equipment

Quick View
$10.99
  (36)
    • Check Price
      • SINCLAIR POLY LOADING BLOCK - 50 ROUND SINCLAIR INTERNATIONAL

      • These 50 round blocks are machined from " material and are anexcellent choice for short to medium length cases. See chart for thecorrect size. Note: The #PB09 block only has 32 holes due to thecase head size. S blocks have shallower holes for short cases. Big Book Catalog, Issue:68, Page:537 Sinclair, Issue:5B, Page:080

1200 PRO TUMBLERS LYMAN

sinclairintl reloading equipment

Quick View
$59.99 - $71.99
  (8)
    • Check Price
      • 1200 PRO TUMBLERS LYMAN

      • Lyman’s best-selling tumbler, the 1200 Pro is a great entry-level tumbler at an entry-level price, with an added bonus. It also features a built-in sifter lid for quick and easy media separation, so it saves you the cost of buying a separate sifter. Heavy duty, thermally protected motor runs smooth and quiet. Holds 2 lbs. of media and cleans up to 350 .38 Special cases per cycle. Media not included. 1911, Issue:11, Page:069 Brownells Christmas , Issue:2X, Page:004 Big Book Catalog, Issue:68, Page:539 Mini-Catalogs, Issue:15, Page:020 Sinclair, Issue:5B, Page:073

AMMOMASTER .50 BMG PACK RCBS

sinclairintl reloading equipment

Quick View
$599.99
  (90)
    • Check Price
      • AMMOMASTER .50 BMG PACK RCBS

      • Whether you're just a beginner or a seasoned handloader, the RCBS AmmoMaster will have you reloading the big .50 Browning Machine Gun (BMG) cartridge with precision and accuracy in no time. This all-inclusive, money-saving kit comes with the press, dies, and all the accessories needed to get started. The powerful AmmoMaster Single Stage press is rigged for 1.5 inch dies with a smooth-operating heavy-duty steel crank shaft handle for excellent leverage. The massive 1.5 inch solid steel ram has plenty of height for the fifty. Also included is a set of RCBS .50 BMG 1.5 inch reloading dies, full-length sizer and seater, shell holder, ram priming unit and a trim die. Sinclair, Issue:5B, Page:060

SINCLAIR UPGRADE ITEMS FOR L.E. WILSON TRIMMER CUTTERS SINCLAIR INTERNATIONAL

sinclairintl reloading equipment

Quick View
$13.99 - $69.99
  (21)
    • Check Price
      • SINCLAIR UPGRADE ITEMS FOR L.E. WILSON TRIMMER CUTTERS SINCLAIR INTERNATIONAL

      • We make several items that make using your L.E. Wilson Trimmer more enjoyable. Our Carbide Cutter Upgrade Kit (part #749-009-253) features a carbide cutter and ergonomic crank handle for quick, clean and comfortable cuts and the cutter will stay sharp for as long as you own it. To speed up your trimming further, we are now offering a power screwdriver adapter for our carbide replacement cutter (part #749-010-492). This power screwdriver adapter accepts the carbide cutter and eliminates the need for the black Delrin™ washer included with the Carbide Upgrade Kit. Our power screwdriver adapter for the standard Wilson trimmer cutter (part #749-000-495) replaces the L.E. Wilson crank handle and allows you to use a power screwdriver or drill to power your case trimming and will work for all models of L.E. Wilson case trimmers, including 50BMG. The Sinclair Replacement Crank Handle for L.E. Wilson Trimmer Cutters (part (#749-011-658) is the same ergonomic replacement crank handle we include with our Carbide Upgrade Kit. Like the power screwdriver adapter above, our replacement crank handle will work for all models of L.E. Wilson case trimmers, including 50BMG. Sinclair, Issue:5B, Page:011 Sinclair, Issue:5B, Page:016