Categories


LOUPES OPTIVISOR

gunsmith tools supplies

Quick View
$18.79
 
    • View
      • LOUPES OPTIVISOR

      • Instantly turns prescription or safety glasses into magnifiers for close up work. Pivots out of the way when not needed. Attaches to either right or left side. Precision-ground optical glass. Big Book Catalog, Issue:68, Page:424 Big Book Catalog, Issue:68, Page:481

CUP TIP PUNCH BENCH BLOCK BROWNELLS

gunsmith tools supplies

Quick View
$8.99
 
    • View
      • CUP TIP PUNCH BENCH BLOCK BROWNELLS

      • Delrin® bench block that holds and organizes eight punches.

        Big Book Catalog, Issue:68, Page:466 New Product Supplement, Issue:621, Page:016

Sight Mini-Screwdriver GLOCK

gunsmith tools supplies

Quick View
$1.99
 
    • View
      • Sight Mini-Screwdriver GLOCK

      • Sight Mini-Screwdriver (for GLOCK adjustable rear sight SP 05977 & GLOCK GTL21 / GTL22 laser lights)

        “GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H.  Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H.  The use of Glock on this page is merely to advertise the sale of Glock parts or components.  As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.

COMBINATION TOOL for GLOCK® B & J MACHINE

gunsmith tools supplies

Quick View
$22.95
  (73)
    • Check Price
      • COMBINATION TOOL for GLOCK® B & J MACHINE

      • Handy Tool Makes Glock Sight Changes Easier Easy-to-use tool helps you remove factory front sights and install aftermarket sights. The punch is just the right size for depressing front sight center spreader; hex wrench holds and tightens the small retaining nut for the replacement sight. Non-slip knurled grip. “GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H.  Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H.  The use of Glock on this page is merely to advertise the sale of Glock parts or components.  As indicated in the product descriptions, not all parts and accessories on this site are official Glock products. Big Book Catalog, Issue:68, Page:516 Law Enforcement / Police Store, Issue:08, Page:055 New Product Supplement, Issue:514, Page:000

ROOM TEMPERATURE NICKEL STRIPPER BROWNELLS

gunsmith tools supplies

Quick View
$59.99
  (86)
    • Check Price
      • ROOM TEMPERATURE NICKEL STRIPPER BROWNELLS

      • Strips All Types Of Nickel Plating Without Heating Or Agitation Convenient, easy-to-mix and use liquid completely removes both electrolytic and electroless nickel from steel, copper and copper alloys without heating or agitation. Safe and simple to use; usual stripping time is 30 minutes to 4 hours. Re-bottle and use again and again. Gives off strong, ammonia odor, use with adequate ventilation. Cannot ship outside Continental United States. Ship UPS Ground only within U.S. Big Book Catalog, Issue:68, Page:434

SERVICE KIT FOR REMINGTON 870, 1100 & 11-87 BROWNELLS

gunsmith tools supplies

Quick View
$80.99 - $359.99
  (96)
    • Check Price
      • SERVICE KIT FOR REMINGTON 870, 1100 & 11-87 BROWNELLS

      • Factory-Type Tools For Armorers And Gunsmiths; The Right Tools For 870 Work-Add Ons Available For The 1100 & 11-87With the help of the fine folks at Remington, the armorer and gunsmith can now have a kit with tools we have adapted from ­factory designs for repairing and maintaining what has probably become the world's most popular pump shotgun—the Remington 870. Special thanks has to go to the entire Remington organization for recognizing the importance of proper tools to the gunsmith. This tool kit makes it easier for the ­armorer or gunsmith to repair the 870 at the bench or in the field. Even though some of the tools may seem like overkill, keep in mind that the designs are based on the factory's years of experience and are intended to stand up to constant use. Whether you're a ­department armorer or a civilian gunsmith who sees only sporting 870s, you'll have the right, factory-type tools to take apart an 870, make the repairs, and put it back ­together. Your satisfaction is guaranteed.View all items included in this kit.View the Remington 870 Owners Manual Big Book Catalog, Issue:68, Page:509 Law Enforcement / Police Store, Issue:13, Page:022 Personal Protection, Issue:01, Page:052

MAGNA-TIP® ADJUSTABLE TORQUE WRENCH BROWNELLS

gunsmith tools supplies

Quick View
$79.99
  (16)
    • Check Price
      • MAGNA-TIP® ADJUSTABLE TORQUE WRENCH BROWNELLS

      • Apply An Exact Amount Of Pre-Set Tightening Force; Accepts ALL Brownells Magna-Tip Bits Precision-adjustable torque driver ensures that you apply the exact amount of leverage needed to accurately tighten any gun screw, including action screws and scope ring/mount screws. Adjustable from 15 to 70 in-lb. in 1 in-lb. increments to eliminate guesswork and prevent under- or over-tightening screws - no more stripped threads or broken-off screw heads. The 1/4" magnetic hex drive socket accepts ANY Brownells Magna-Tip bit - plus, 6 bits commonly needed for gun work are included! Ergonomic, rubber-coated handle gives you a secure grip for maximum leverage and even transfer of tightening force. To change torque setting, simply turn the orange collar to the desired setting indicated through the easy-to-read window scale. A self-limiting cam-over clutch "clicks" free when the specified amount of torque is reached, making over-tightening impossible. Each driver is hand calibrated and inspected, and comes with a handwritten certification card.

1911 SLIDE FITTING BARS BROWNELLS

gunsmith tools supplies

Quick View
$29.99 - $349.99
  (21)
    • Check Price
      • 1911 SLIDE FITTING BARS BROWNELLS

      • Remove Slide "Play" Accurately & ProfessionallySurface ground and hardened tool steel bars in ten thicknesses - Recommended by agency armorers and top pistolsmiths as the most accurate way to remove vertical slide “play” from the 1911 Auto, its variations and copies. May be slower than the quick-and-dirty methods, but gives an infinitely more accurate and professional job. Basic procedure as follows: Measure gun’s slide rail thickness; place closest-sized Slide Fitting Bar in frame “way”; tap frame rail with light hammer to close the “ways” space down to match the slide rail thickness. Complete instructions included. 1911, Issue:11, Page:053 Big Book Catalog, Issue:68, Page:150 Sinclair, Issue:1A, Page:112 Sinclair, Issue:1A, Page:113 Sinclair, Issue:1A, Page:114 Sinclair, Issue:1A, Page:115 Sinclair, Issue:1A, Page:116 Sinclair, Issue:1A, Page:117 Sinclair, Issue:1A, Page:118 Sinclair, Issue:1A, Page:119 Sinclair, Issue:1A, Page:120

ARMORER'S/SHOP TRIGGER WEIGHTS CUSTOM GUNSMITHING, INC.

gunsmith tools supplies

Quick View
$15.95 - $219.99
  (7)
    • Check Price
      • ARMORER'S/SHOP TRIGGER WEIGHTS CUSTOM GUNSMITHING, INC.

      • Accurately Checks Single-& Double-Action Trigger Pulls From 2 1b. to 17-3/4 lb.Simple, reliable, add-on weight system measures pull on all types of triggers, handguns, rifles and shotguns. Weights stack and thread into 2 lb. base weight and measure from 2 lb. to 17 lb. in lb. increments. Big Book Catalog, Issue:68, Page:490

GUNSMITH REPLACEABLE PIN PUNCH SET BROWNELLS

gunsmith tools supplies

Quick View
$9.99 - $24.99
  (71)
    • Check Price
      • GUNSMITH REPLACEABLE PIN PUNCH SET BROWNELLS

      • Take The Blow($) Out Of Replacing Pin PunchesFinally! What we think is the answer to the pin punch headache that has plagued us - and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now - Just Replace The Tip! Handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof C.R.S. Steel - Tensile strength of over 140,000 psi (Min.). Replaceable Punch - the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to Rc 58-60. Heads are annealed to Rc 42-45. They come in two lengths and can be ground down to exact length required - custom punches with minimum investment. Big Book Catalog, Issue:68, Page:467 Big Book Catalog, Issue:68, Page:509

NYLON/BRASS DRIFT PUNCH BROWNELLS

gunsmith tools supplies

Quick View
$3.39 - $22.99
  (88)
    • Check Price
      • NYLON/BRASS DRIFT PUNCH BROWNELLS

      • 6 Indispensable Mar-Proof Punches Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: Nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; Brass for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Single replaceable non-marring nylon punch with .165 diameter used for removing trigger plate pins from 870, 1100 and 1187. Supplied as: Basic Set with two 5/16" diameter tips (one Nylon, one Brass) and one Handle. 4-Way Set includes four Handles, one 5/16" Nylon Tip; plus one each, 3/16", ¼" and 5/16" diameter Brass Tips. 6-Way Set adds ¼" and 5/16" diameter, Aluminum Tips and 2 more handles to the 4-Way Set. Big Book Catalog, Issue:68, Page:465 Cowboy Action, Issue:03, Page:029 Law Enforcement / Police Store, Issue:08, Page:058 New Product Supplement, Issue:566, Page:002

CERROSAFE® CHAMBER CASTING ALLOY BROWNELLS

gunsmith tools supplies

Quick View
$24.99 - $45.99
  (50)
    • Check Price
      • CERROSAFE® CHAMBER CASTING ALLOY BROWNELLS

      • Never Wears Out- Use Over And OverThere are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158 - 190 F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun. Big Book Catalog, Issue:68, Page:494 Big Book Catalog, Issue:68, Page:508

1911 LUG CUTTER BROWNELLS

gunsmith tools supplies

Quick View
$53.99 - $82.99
  (64)
    • Check Price
      • 1911 LUG CUTTER BROWNELLS

      • Recuts Lug For A Tight Fitting Barrel That Improves AccuracyHand operated, carbide cutter easily trims excess material from the bottom barrel lug when fitting custom or factory barrels to 1911 Autos. Cuts barrel lugs parallel, and with the correct height and radius, to help produce the best possible lockup. Use .186" cutter first, then progress to the .195" cutter if more material needs to be removed. Follow with careful hand fitting to achieve a firm, non-binding barrel-to-slide fit. Start small and check your work often. It is possible, with some slide/barrel combinations, that the .195" cutter could remove more material than necessary. Fits all 1911 Auto, Commander and Officers ACP, single- and double-stack frames. 1911, Issue:11, Page:055 Big Book Catalog, Issue:68, Page:152 New Product Supplement, Issue:572, Page:003

REPAIR RECORD/INVOICE BROWNELLS

gunsmith tools supplies

Quick View
$24.99 - $79.99
  (33)
    • Check Price
      • REPAIR RECORD/INVOICE BROWNELLS

      • Neat, Easily filled Out, Easily Filed Form Organizes Your RepairsTwo choices of gunsmith-designed forms for recording incoming repairs and tracking them through the billing process. Both styles have plenty of room to note requested repairs, work performed, and special notes by the gunsmith. Also includes space for gun and owner info and check-off blocks for items left with the gun (sling, lens covers, scope, etc.). Modern impression paper makes a duplicate copy without the mess of carbon paper. Plenty of room at the top to print or stamp your store or shop logo. 2-PART FORM - 2-part form has one copy for your customer and one that stays with the gun for your records. Blank space for the job number allows you to use this form with the Brownells Gunsmith Claim Checks. Simply record the number provided on the claim check in the blank spot on this form. Standard, 8½" x 11" size. 3-PART FORM - All-in-one, 3-part form includes has one copy for your customer, one for your bookkeeper, and one to stay with the gun. Each form is consecutively numbered for easy job tracking. Compact 5½" x 91⁄8" size, and punched to fit a 2-ring clipboard with standard 2¾" hole spacing. Big Book Catalog, Issue:68, Page:527 New Product Supplement, Issue:621, Page:017

ROLL PIN PUNCH SET BROWNELLS

gunsmith tools supplies

Quick View
$9.99 - $109.99
  (49)
    • Check Price
      • ROLL PIN PUNCH SET BROWNELLS

      • Remove & Install Roll Pins The Professional WayWe combined 19 of our most popular roll pin punches and added a handy bench block to come up with the perfect punch set for the busy shop or department armor. Easily start, remove, and install spring pins and roll pins in firearms without damage to the pin or firearm. Features (5) holder punches, (7) starter punches, and (7) standard punches that can easily handle any job out there. Made from solid steel, with parallel-ground shanks and knurled handles. Also includes a non-marring, nylon drift punch that won’t damage or scrape delicate surface finishes. Machined, Delrin® bench block holds and organizes all the punches for easy access. Holder punches cup and hold roll pins, keeping them aligned for easy starting without pinching or binding. Especially good on the tiny, hard-to-grab ones, or those in tight places. Features a 1/16" diameter punch that is notched to clear the M16/AR-15 rear sight, plus a 3.5mm diameter punch for holding the pin that retains the breech block on Sig handguns. Finish driving with a standard roll pin punch. Starter punches are used to start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft gives more control by putting your hand closer to the pin and prevents bending the longer, standard roll pin punches. Standard punches are used to finish drive the roll pin or spring pin after it’s started. Starter and standard roll pin punches feature a special tip that centers inside the hollow pin to help prevent slippage. Complete set includes bench block, also available separately. Big Book Catalog, Issue:68, Page:466 New Product Supplement, Issue:621, Page:016

BISLEY GUNSMITHING VISE LOTHAR WALTHER PRECISION TOOL

gunsmith tools supplies

Quick View
$274.99
  (23)
    • Check Price
      • BISLEY GUNSMITHING VISE LOTHAR WALTHER PRECISION TOOL

      • Improved & Updated Version Of The Famous English-Made Original; Multi-Positional For Unlimited Access To Your WorkPrecision, German-made gun vise modernizes the original Parker Hale design so popular decades ago with English shooting ranges for detailed gun cleaning and maintenance. Cast from high tensile strength aluminum alloy, the Bisley vise is compact and light enough to take anywhere, yet tough enough to handle jobs bigger than expected. Two sets of parallel clamping jaws rotate a full 360 in the same plane to provide unlimited versatility and access to your work. Simple and reliable, spring-loaded, cog-locking system allows instant one-hand adjustment by pulling back on the rear jaw and rotating it to any of 15 different positions in 22.5 increments. Hardened and ground, steel jaw inserts on one side handle small parts and many intricate tasks around the shop; oval shaped jaws with cork padding on the opposite side allow non-mar clamping of barrels, receivers, and large irregularly shaped objects. Polymer adjustment knob with threaded steel bushing glides along the vise screw with exceptional smoothness for precise tension control. Heavy duty base with steel clamping screw and T-handle make the Bisley vise extremely solid, portable and quick to mount and remove on work platforms from 1 to 2" thick. Big Book Catalog, Issue:68, Page:461 New Product Supplement, Issue:611, Page:017

1911 AUTO OVERSIZED STOCK BUSHINGS & TAP BROWNELLS

gunsmith tools supplies

Quick View
$12.99 - $99.99
  (41)
    • Check Price
      • 1911 AUTO OVERSIZED STOCK BUSHINGS & TAP BROWNELLS

      • Professionally And Easily Replace Stripped-Out Bushing Holes-No Welding Or DrillingEasily and professionally solves the problem of stripped out stock bushing holes. Special tap cleans out stripped frame threads, cuts new ones without pre-drilling. Matching bushing screws right in, uses original grip screw. Will save your life when polishing/bluing, accurizing .45's! 1911, Issue:11, Page:041 Big Book Catalog, Issue:68, Page:138 New Product Supplement, Issue:554, Page:026 Sinclair, Issue:1A, Page:038

PROFESSIONAL GUNSMITH NEEDLE FILE SET FRIEDR. DICK GMBH

gunsmith tools supplies

Quick View
$12.99 - $119.99
  (91)
    • Check Price
      • PROFESSIONAL GUNSMITH NEEDLE FILE SET FRIEDR. DICK GMBH

      • Finest Professional Gunsmith QualityFinest Professional Quality Gunsmith Needle Files in set of 12 assorted shapes. Made of best materials to rigid quality standards. Cuts are deep and durable. Knurled handles for no-slip use or convenient lock-up in Needle File Handles shown below. Comes in heavy-duty, see-through, pocketed roll with snap closure. Protects files, yet gives immediate access to shape wanted. Sold in sets or singles. Big Book Catalog, Issue:68, Page:477 Law Enforcement / Police Store, Issue:03, Page:046

CONTOUR #7, 8 & 9 BARREL SHILEN

gunsmith tools supplies

Quick View
$191.99 - $271.99
  (84)
    • Check Price
      • CONTOUR #7, 8 & 9 BARREL SHILEN

      • Contours #7, 8 & 9 in Chrome Moly or Stainless Steel All the loving care of the best stockmaker and the meticulous attention to detail of the master machinist will not make a gun shoot any straighter than the accuracy capability of the barrel used. And, it is the insides of a barrel, that very small and vital area of lands and grooves over which the gunsmith has no control, that can determine whether the finished work of art is for shooting - or “just for looks”. Craftsmanship . . . not price . . . determines the quality of a barrel. But, by the same token, the customer willing to spend the money for a custom gun is shortsighted indeed, if he starts economizing and orders “just any old barrel so long as it’s cheap”. Furthermore, he is jeopardizing your reputation as a gun builder by making such a request. We, as your supplier, are laying our reputation (and yours, too!) on the line by offering you barrel blanks. They have got to be good or we are in trouble! Big trouble!! We must never sell you anything but that which will enlarge your stature with your trade. And, we feel that the Brownell Barrel, made for us by Ed Shilen, will do just that! Shilen barrels, either chrome moly or Stainless, are rifled with six lands and grooves by the “Cold Forming” process using carbide dies made in Shilen’s own plant under the most rigid controls. This rifling method achieves extremely close inside uniformity from breech to muzzle. Finished barrels are air-gauge inspected (air-gauged sensitivity is .00005" - five-one-hundred-thousandths!) and 6X borescope in- spected. All barrels, .22 through .30 caliber have groove tolerances within .0005" and uniformity within .0003". No straightening is done, and all barrels are completely stress-relieved. All stainless steel barrels are hand lapped at the factory. Only those barrels passing all spec tests are offered to the trade. Any barrel even slightly “suspect” is started through the production process again and bored to a large caliber. In no other way can quality and reputation be maintained. Slightly more expensive to produce - but vastly greater in quality and ultimate performance. Big Book Catalog, Issue:68, Page:177

POLYMER ARMORER'S BLOCK & TOOLING PLATE APEX TACTICAL SPECIALTIES INC.

gunsmith tools supplies

Quick View
$24.99 - $29.99
  (32)
    • Check Price
      • POLYMER ARMORER'S BLOCK & TOOLING PLATE APEX TACTICAL SPECIALTIES INC.

      • Supports a polymer frame pistol for armory work and detail disassembly. Pre-positioned bosses, slots and holes remove pressure from critical function surfaces while pins are driven in and out. Thumb Safety and Magazine disconnect drop into holes and slots to prevent damage no matter what position they are in. High Density Polymer construction prevents marring of the frame while driving pins in and out. Retaining slots on each side of the block hold the striker making removal and installation of the striker spring a breeze. One side is for the 45 striker and the other is for the 9/40/357 striker. Moveable bosses are easily adjustable to position frames quickly and easily. Raised walls on each side of the block position the trigger bar within the trigger to easy trigger swapping. Apex logo and contact information cast directly into the body of the block for easy identification and access to Apex’s tech support staff. The Armorer's Tooling Plate is designed to attach directly to the underside of the Apex Piolymer Armorer's Block, providing a raised surface for you to work on your M&P and Glock Pistols.  The tooling plate has snap locks and slots to hold the 1/8" custom roll pin punch and 1/16" allen wrench.  Rubber feet grip the work surface, allowing for a sturdy hold while working.  a ring magnet on the underside of the plate will prevent magnetic parts from escaping. Brownells Christmas , Issue:4X, Page:017 Big Book Catalog, Issue:68, Page:515 Mini-Catalogs, Issue:03, Page:016

XS® ARMORER'S BLOCK FOR AR PLATFORMS XS SIGHT SYSTEMS

gunsmith tools supplies

Quick View
$75.00
  (46)
    • Check Price
      • XS® ARMORER'S BLOCK FOR AR PLATFORMS XS SIGHT SYSTEMS

      • This upper receiver armorer's block will allow the gunsmith or enthusiast to assemble, modify, or maintain most AR pattern modern sporting rifles. While most blocks will only fit one specific style, the XS Universal block provides the versatility need to work on any AR pattern upper receiver: AR-15, AR-10, SR25, or DMPS GII. This versatility, plus the reliability of an XS Sights Made in the USA aluminum product, is a one size fits all solution.

SERIES II STONING FIXTURE POWER CUSTOM

gunsmith tools supplies

Quick View
$33.99 - $189.99
  (85)
    • Check Price
      • SERIES II STONING FIXTURE POWER CUSTOM

      • Precise, Controlled Stoning Of Semi-Auto Hammers And Sears For Perfect Trigger PullsEliminates the guesswork and gives an accurate, repeatable method to achieve a crisp, clean-breaking trigger pull on semi-automatic firearms. Individual, easy-to-change Adapters attach to a precision-ground indexing elevator column and clamps the hammer in the right position for correct stoning with the specially ground Series II India Stone or Series II Hard Arkansas Stone. Adjustable design lets you change hammer angle to meet the shooters’ precise needs. Series II India Stone or Series II Hard Arkansas Stone required for use. Purchase separately. Universal Adapter (described below) adds incredible versatility. 1911, Issue:11, Page:062 AR-15, Issue:10, Page:084 Big Book Catalog, Issue:68, Page:089 Big Book Catalog, Issue:68, Page:157 Big Book Catalog, Issue:68, Page:481

1911 ARMORER'S BLOCK 10-8 PERFORMANCE LLC

gunsmith tools supplies

Quick View
$49.99
  (11)
    • Check Price
      • 1911 ARMORER'S BLOCK 10-8 PERFORMANCE LLC

      • For Fast, Easy Maintenance, While Protecting Pistol & Hands From DamageHandy bench block machined from super-tough, glass-reinforced nylon supports 1911 pistol components so you can perform a variety of repair, assembly/disassembly, and accurizing tasks quickly and easily. Securely holds the frame on its side, so you can work on it without risk of damaging the finish. Helps you check hammer/sear engagement, remove hammer strut pin, remove mainspring housing, and holds thumb safety for easy filing of sear stop stud engagement surface. Use to tension the extractor off the slide, so you don’t risk scratching the slide, and retain the extractor while filing and honing the claw. Holds the barrel during link pin removal, with blind holes to catch the pins so they don’t get lost. You can even place the frame between two blocks and clamp it in a bench vise for slide fitting. 1911, Issue:11, Page:054 Brownells Christmas , Issue:4X, Page:016 Big Book Catalog, Issue:68, Page:151 Mini-Catalogs, Issue:05, Page:008 New Product Supplement, Issue:621, Page:015

LIVE PILOT FINISH CHAMBER REAMER MANSON PRECISION

gunsmith tools supplies

Quick View
$130.00 - $139.99
  (69)
    • Check Price
      • LIVE PILOT FINISH CHAMBER REAMER MANSON PRECISION

      • Cuts A Smooth, Precise Chamber With Less Chance Of Rifling DamageRemovable (live) pilot greatly reduces the risk of scratching the lands when cutting the chamber to final dimensions, so you get the best possible chambering job for maximum accuracy. Snug-fitting pilot helps provide extra-stable “live center” alignment to maintain proper chamber-to-bore alignment. Precision ground from high speed M7 tool steel for smooth, clean cutting and maximum service life. Includes one pilot for caliber listed. Big Book Catalog, Issue:68, Page:493 New Product Supplement, Issue:602, Page:021

1911 ANODIZED BUSHING WRENCH BROWNELLS

gunsmith tools supplies

Quick View
$19.99 - $24.99
  (47)
    • Check Price
      • 1911 ANODIZED BUSHING WRENCH BROWNELLS

      • Non-Marring Aluminum Gets The Tightest Bushings LooseThe perfect tool for every 1911 owner’s range bag or cleaning kit. Precision machined for a close fit to Government Model and Officers bushings. The extra thick, contoured handle fits comfortably in your hand; has plenty of heft for a good, solid grip. Turns the tightest bushings without slipping. Enhanced model has a handy flange that retains the recoil spring plug as you twist the bushing free. No more flying springs or plugs! 1911, Issue:11, Page:053 1911, Issue:11, Page:058 Brownells Christmas , Issue:4X, Page:016 Big Book Catalog, Issue:68, Page:150 Big Book Catalog, Issue:68, Page:153 Law Enforcement / Police Store, Issue:09, Page:107 Mini-Catalogs, Issue:01, Page:009 New Product Supplement, Issue:581, Page:012 Personal Protection, Issue:01, Page:051

HAWKEYE BORESCOPE KIT W/ FOCUSING EYEPIECE GRADIENT LENS

gunsmith tools supplies

Quick View
$769.99
  (42)
    • Check Price
      • HAWKEYE BORESCOPE KIT W/ FOCUSING EYEPIECE GRADIENT LENS

      • Money saving kit features an adjustable focus, 17" Borescope, light source and a 90° Mirror Attachment for close-up, direct viewing of bore, chamber, throat and crown. Everything packed in an all aluminum carry case. Includes lens cleaning solution and instructions. Brownells Christmas , Issue:5X, Page:021 Sinclair, Issue:5B, Page:229

BRASS ONE CALIBER SET BROWNELLS

gunsmith tools supplies

Quick View
$150.99 - $151.99
  (13)
    • Check Price
      • BRASS ONE CALIBER SET BROWNELLS

      • Square Up & Chamfer Rifle and Handgun Muzzles P Brass Bore PilotSet includes: one, 90 facing cutter to square a muzzle after shortening, or repair damage; one, 45 chamfering cutter to break the edges of the rifling for a clean bullet exit or chamfer a revolver cylinder mouth for quick reloads; plus one handle that fits either cutter and one brass bore pilot. Interchangeable pilot keeps cutter properly aligned. Purchase extra pilots to use one cutter for many different calibers. Pilots for other calibers available separately.Select one of the following for other rifle/handgun muzzles, cylinder facing & chamfering tools. Chamfering & Facing Combo Sets 45 Cutter & Steel Pilot Steel One Caliber Set 45 Cutter & Brass Pilot 90 Cutter & Steel Pilot Steel Pilot Only 90° Cutter & Brass Pilot Brass Pilot Only Big Book Catalog, Issue:68, Page:497 New Product Supplement, Issue:572, Page:004